dc.contributor.advisor |
Svoboda, Josef |
cze |
dc.contributor.author |
Loudová, Petra |
|
dc.date.accessioned |
2011-09-07T05:41:02Z |
|
dc.date.available |
2011-09-07T05:41:02Z |
|
dc.date.issued |
2011 |
|
dc.identifier |
Univerzitní knihovna (sklad) |
cze |
dc.identifier.uri |
http://hdl.handle.net/10195/41020 |
|
dc.description.abstract |
Tato práce byla zhotovena ve spolupráci s firmou PEMAX PRINT se sídlem v Poděbradech, která se zabývá tiskem samolepicích etiket a jejich úpravou. Zde nastával čas od času problém s neúplným dotvrzením vrstvy UV laku na potištěném materiálu.
Úkolem této bakalářské práce bylo zjistit, z jakého důvodu tento problém nastává. V průběhu práce byly sledovány a posuzovány vlivy úpravy povrchů substrátu na kvalitu termotisku pomocí jednoduché zkoušky přilnavosti a orientační zkoušky oděru v provozních podmínkách. Dále pomocí zkoušky odolnosti potištěných vzorků vůči oděru v laboratorních podmínkách. Výrazně vyšší odolnost vůči oděru byla zřejmá u potištěných a následně lakovaných vzorků. Laboratorně bylo zkoušeno vytvrzování UV laku bez a poté s přídavkem fotoiniciátoru pomocí Fourierovy transformace infračervených spekter (FTIR). FTIR spektrometrem byla naměřena spektra nevytvrzených, vytvrzených i částečně vytvrzených vzorků UV laku v závislosti na dávce ozáření.
Použití UV laku s přídavkem fotoiniciátoru umožňuje urychlení vytvrzení potištěného materiálu UV lakem. Přidání fotoiniciátoru do UV laku by mohlo být jednou z možných variant řešení tohoto problému. |
cze |
dc.format |
50 s. |
cze |
dc.format.extent |
1504275 bytes |
cze |
dc.format.mimetype |
application/pdf |
cze |
dc.language.iso |
cze |
|
dc.publisher |
Univerzita Pardubice |
cze |
dc.rights |
Práce není přístupná |
cze |
dc.subject |
etikety |
cze |
dc.subject |
flexotisk |
cze |
dc.subject |
UV laky |
cze |
dc.subject |
termální přenosový tisk |
cze |
dc.subject |
přímý termální tisk |
cze |
dc.subject |
labels |
cze |
dc.subject |
flexo |
cze |
dc.subject |
UV varnishes |
eng |
dc.subject |
thermal transfer printing |
eng |
dc.subject |
direct thermal printing |
eng |
dc.title |
Vliv úpravy povrchu substrátu na kvalitu termotisku |
cze |
dc.title.alternative |
The effect of substrate sasurface modification on the quality of thermoprinting |
eng |
dc.type |
bakalářská práce |
cze |
dc.date.accepted |
2011 |
cze |
dc.description.abstract-translated |
This work was made in the cooperation with PEMAX PRINT located in Poděbrady which deals with self-adhesive label printing and treatment. There occurs the problem of incoplete confirmation of the UV warnish layer on the printed material from time to time.
The task of this thesis was to find out why this problem occurs. During the investigation, the effects of substrate surface treatment on the quality of thermal printing were monitored and assessed with the use of the simple test of adhesion and orientational test of attrition in operational conditions. Furthermore also with the use of the test of the printed samples to abrasion in laboratory conditions. Significantly higher resistance to abrasion was evident in the printed and then varnished samples. Using the laboratoryequipment, there was tested curing of the UV varnish with and then without the additions of photoinitiators using the Fourier transformation of infra ? red spectroscopy (FTIR). FTIR spectrometer measured the spectrum of uncured, partially cured and cured samples of the UV layer, depending on the amount of radiation.
The use of the UV layer with the addition of the photoinitiator enables the curing acceleration of the printed material by the UV layer. Adding photoinitiators in UV varnish might be one of possible variants of solving of this problem. |
eng |
dc.description.department |
Katedra polygrafie a fotofyziky |
cze |
dc.thesis.degree-discipline |
Polygrafie |
cze |
dc.thesis.degree-name |
Bc. |
cze |
dc.thesis.degree-grantor |
Univerzita Pardubice. Fakulta chemicko-technologická |
cze |
dc.identifier.signature |
D24991 |
|
dc.thesis.degree-program |
Polygrafie |
cze |
dc.description.defence |
doc. Ing. Michal Veselý, CSc. - Které vzorky byly zalakovány upravenou formulací UV laku?
prof. Ing. Petr Kalenda, CSc. - Jak jste stanovila stupeň konverze lakových vrstev? Jakým mechanismem probíhá polymerace Uv laku?
doc. Ing. Petr Němec, CSc. - Jak poznáte 100% konverzi v FTIR? |
cze |
dc.identifier.stag |
9602 |
cze |
dc.description.grade |
Dokončená práce s úspěšnou obhajobou |
cze |
dc.description.grade |
Dokončená práce s úspěšnou obhajobou |
cze |